If you would like to become a TecAlliance customer or have questions about our products, please contact us or vistit the TecAlliance Online Shop to buy the. Working quickly, Tweddle Group collaborated with Toyota to develop a customized New-Generation TechDoc infrastructure NG TD for authorized dealerships and TD1 for independents.
Vsaka uporaba vsebine na nain, ki ni izrecno dovoljen, pomeni kritev avtorskih pravic in bo ustrezno preganjana.
Anyhow, the fog light indicator light on the tachometer works fine so it would be redundant to have the switch light working anyways.įinal note.the fog lights don't seem to be super bright, which is fine. After registration you can get access to further application information as well as informative downloads and trainings in our customer area only for existing customers. Brez predhodnega soglasja TechDoc je strogo prepovedano podvajati podatke in bazo podatkov ter jih razirjati in/ali napeljevati tretje osebe k izvajanju taknih dejavnosti. Personal information of some 3. There wasn't a dark green wire feeding the dimmer switch, but there was a light green one.I tapped into that, but it doesn't light up the switch. 3.1 million customer records possibly stolen in Toyota hack.
The ONLY thing that didn't work in this install is the switch light, but i could care less about that.
The switch wiring harness had different colored wires than yours, but thanks to your pic and description, it was easy to figure out how to cross reference them.
The panel has 2 built-in plastic clips on either side that come out with a little coaxing, so be gentle. Removing the panel below the steering column is a little tricky. Specifically, disconnect the black (negative -) terminal I never used those red clamp/connectors before in my life, but my bro-in-law had some lying around and they were easy to install.īefore doing the interior wiring, disconnect the battery as advised. The light wiring harnesses are right behind them. getting to the foglight blanks/templates and popping them out was easy. > pop and prop the hood, and remove this thing - what is it called? you can use a flat head instead of the special tool for the 1 fastener, the other 8 come out real easy.Ģ009 2010 TOYOTA RAV4 JDM OEM FOG LIGHTS KIT CLEAR 09 | eBay > install switch in dash and reinstall the previously removed panelsĪt this point you have a complete OEM fog wiring setup! if you wanted to slap bulbs on the OEM wiring and reconnect the battery to test, it should all work.
(if your ebay wiring is like mine, this will be the remaining black wire.) Upgrade or repair entitlement The fact that a piece of technical information which relates to a specific upgrade or repair work for any specific range of vehicles has been published on this website. > if your switch has an illumination light like the ebay, splice the illumination wire into the Green wire on the back of the dash dimmer knockout switch. (if your ebay wiring is like mine, this will be the Yellow wire.) there's a good grounding spot to the bottom left of the driver's foot-well, just use a self-tapping screw. > connect the other lead from the switch to a good ground point.
(if your ebay wiring is like mine, this will be the Red wire on the end of the connector.) make sure to zip-tie and secure the wiring cleanly along the OEM wiring path. If you dont know your current password, contact your local IS Support Team this time. > tap into the grey fog wire with a Tap Splice, a red 22-18 AWG is best, and insert one end of your fog on/off switch to the circuit. Registering email address will allow you to set up a new password for yourself in future. A non-original car part carrying an OEM number demonstrates that the part meets stringent car manufacturer standards and its parameters and technical specifications are identical to original equipment. Car manufacturers use them to mark every part inside their cars.
Toyota Alphard / Vellfire Service information library 04.2008 - 08.2012ĢAZ-FE - 2.To prep the switch harness for use, remove the wire loom and cut the wires about 2-3 feet from the switch connector, making sure to cut past the point at which the 2 red wires are spliced together. An OEM number is a unique code containing letters and digits.